Flashing Tronxy X5S Factory Control board USB Cable only

Ok so Scott here again, this time I decided to go ahead and take things to a simple level based off a write up done by Syed Muhammad Shaheryar. I have seen so many comments and issues with people flashing firmware to their factory TronXY X5S control board, now this should work for flashing the firmware on the X3S as well but the firmware I included will need some edit work unlike for the X5S. This Version of Arduino IDE will work just like any other but it can be installed on a thumb drive or SD card  and moved from one computer to the next without having to install anything on that computer. it should also work on other boards but I have not tested it.

Continue reading
  4178 Hits
  43 Comments
Recent Comments
Scott Worthington
By doing it this way You can copy the same file onto a thumb drive and run off ant windows computer. and use to flash other boards... Read More
Saturday, 24 February 2018 01:52
Scott Worthington
If you do not fallow it step by step this might happen. If you had arduino installed before you must remove it first as this versi... Read More
Tuesday, 06 March 2018 19:23
Scott Worthington
While I have seen this work on Windows 10 I have also seen it be an issue if you have another Windows 7 computer I would try that.... Read More
Tuesday, 06 March 2018 19:32
4178 Hits
43 Comments

Power Supply Fan Replacement

           Ok So Scott here again recently I started to hear a noise coming from my power supply unit (PSU), so I decided to replace the fan with a quiet one. I choose to use a mini kaze (60mm) fan to keep it quiet as well as work well to keep the PSU cool. Normally I start by showing you tools needed but in this case all I needed was a screw driver so I’ll skip that step and add in a the normal caution to make sure the PSU is turned off and unplugged.

Continue reading
  1036 Hits
  1 Comment
1036 Hits
1 Comment

Mk7 / Mk8 HOTEND ASSEMBELY REBUILD

      Ok so Scott here again lately I have been seeing a lot of post and comments about the factory Tronxy hotend so I figured I would go ahead and write up a quick tech article. While this is not the only way to rebuild or assemble the hotend assembly this is the way I do it. This also works on the E3D hotends I have but the throat is different on them. So let’s start with a few tools.

Continue reading
  2307 Hits
  2 Comments
Recent Comments
Scott Worthington
this part of the site does not have a upload options. the forum does.
Thursday, 15 February 2018 22:53
2307 Hits
2 Comments

Flashing firmware on to stock TronXY X5S control board

          This tutorial will help you flash some real firmware on to your stock TronXY X5S control board, using a separate Arduino Uno board as the programmer. It’s not meant for any other board, period. Just the stock one specifically. No others. If you try it on a different board and it doesn’t work, don’t say I didn’t warn you.

It is also written under the assumption that you're running Windows. If you're on a different operating system you'll need to take the appropriate equivalent steps. If you don't know how to do that you'll need to find a different set of instructions. :)

Continue reading
  5293 Hits
  20 Comments
Recent Comments
Scott Worthington
I posted a copy of my full firmware in the downloads area of the forum. so no need to edit the files or anything.
Wednesday, 17 January 2018 22:46
Norman Gilman
What advantages does this have over the stock 1.1.7 firmware currently on my new X5S?
Thursday, 18 January 2018 17:33
Scott Worthington
factory firmware is not a true 1.1.7. 1.1.8 has assisted manual bed leveling lot faster responce from the controls and reads the s... Read More
Thursday, 18 January 2018 17:38
5293 Hits
20 Comments

Site updates

Well we are still at work on the background stuff to get more information on the site and more background work done. Thanks to Yi Ong we have a new How-to up and it's quickly become the most viewed article yet. Still looking for more if any of you write one feel free to let us know because we would love to be able to post it here for all to see. We also added a donation button on the bottom of the site to the site fund itself and future upgrades that are found to be needed.   Looking forward to seeing more activity in the forum... Don't forget the stop in and check out out gallery where we have videos and downloads amoung other things.

  458 Hits
  0 Comments
458 Hits
0 Comments

Tronxy X5S Build

What’s in the box?

 

Continue reading
  4717 Hits
  1 Comment
4717 Hits
1 Comment

We Have Gone Live

We Have Gone Live.

Welcome you all new members who have joined us.

While the site is new there might be a few buggy issues, and to help us give you a great user experience let us know if you find something wrong.

Also if you think of somthing to add to any of the main areas of the site do tell us.

Many Thanks For Joining.

The Team.

Continue reading
  641 Hits
  0 Comments
641 Hits
0 Comments

To keep the site live and make improvements Please consider Donating. Thank you for your donation.