What's New In The 3D Printer World

Tronxy XY-3 Rundown

OK Scott Here again. So I over the last few years and all I have decided to change how I do my printer rundowns a little. Some might call them reviews but that’s a term I don’t care for because to many reviews are bias. Therefore I do what I call rundowns.  Where I give my overall thoughts on the printer along with a list of exactly what I found on the printers good and bad these are 100% my view of things I will give good and bad no matter what. So for this article I’m going to do a RUNDOWN on the Tronxy XY-3 (12V version) Plus which I have had for just over a month now.

 

Continue reading
  16161 Hits
  0 Comments
16161 Hits
0 Comments

Rundown on printers

      OK Scott here again like normal. A lot of people have asked me to do reviews or feedback on different printer or ask me what I think of a new printer out and while I can give my overall view of the new printers as to what I can see being good or bad about them I can not and will not do any true rundown on any printer or product I have not used. With that said I have offered my thoughts on several printers that I do not own but please always keep in mind it's only based on what I see....  while I have other printers I’m not going to include them here as one is no longer on the market and the other is custom built by me (still in process).

Continue reading
  21654 Hits
  0 Comments
21654 Hits
0 Comments

Flashing Tronxy X5S Factory Control board USB Cable only

Ok so Scott here again, this time I decided to go ahead and take things to a simple level based off a write up done by Syed Muhammad Shaheryar. I have seen so many comments and issues with people flashing firmware to their factory TronXY X5S control board, now this should work for flashing the firmware on the X3S as well but the firmware I included will need some edit work unlike for the X5S. This Version of Arduino IDE will work just like any other but it can be installed on a thumb drive or SD card  and moved from one computer to the next without having to install anything on that computer. it should also work on other boards but I have not tested it.

Continue reading
  62431 Hits
  62 Comments
Recent Comments
Scott Worthington
By doing it this way You can copy the same file onto a thumb drive and run off ant windows computer. and use to flash other boards... Read More
Saturday, 24 February 2018 01:52
Scott Worthington
If you do not fallow it step by step this might happen. If you had arduino installed before you must remove it first as this versi... Read More
Tuesday, 06 March 2018 19:23
Scott Worthington
While I have seen this work on Windows 10 I have also seen it be an issue if you have another Windows 7 computer I would try that.... Read More
Tuesday, 06 March 2018 19:32
62431 Hits
62 Comments

Mk7 / Mk8 HOTEND ASSEMBELY REBUILD

      Ok so Scott here again lately I have been seeing a lot of post and comments about the factory Tronxy hotend so I figured I would go ahead and write up a quick tech article. While this is not the only way to rebuild or assemble the hotend assembly this is the way I do it. This also works on the E3D hotends I have but the throat is different on them. So let’s start with a few tools.

Continue reading
  32228 Hits
  4 Comments
Recent Comments
Scott Worthington
this part of the site does not have a upload options. the forum does.
Thursday, 15 February 2018 22:53
Scott Worthington
Normally I start out tightening it before it's cold then heat it up and check make sure it did not change.
Wednesday, 23 January 2019 20:01
32228 Hits
4 Comments

Stepper Driver Current Adjustment

           Well Seeing as How I’m new to writing articles like this and this is the first one I have had published anywhere I am going to take a second to introduce myself a little.

          My Name is Scott; I’m 38 married with four kids, and an Air Force Veteran, I have my associates and bachelor degrees. I also have an electrical and computer numeric controlled (CNC) background. I have two CNC mills as well as a CNC lathe and two 3D printers, which is what brought me here.

          Over the past few months I have started to see more and more questions about setting up and also tuning various 3D printers and their options. These articles will not be published in any order. They will cover whatever comes to mind at the time that I sit down to write. I tend to write the way I think and speak in my everyday life I am straight forward and NONE of that “you must do things this way”……. I will simply be writing how I do things right or wrong, it works for me and I hope it will work for you as well. 

Continue reading
  42880 Hits
  19 Comments
Recent Comments
Norman Gilman
Very comprehensive article. Skimmed some as its getting very late here, but should certainly be useful. Keep 'em coming.
Tuesday, 12 December 2017 23:47
Scott Worthington
Thank you... That was the first of many hopefully I just have to get my head around the next one... but we will take articles writ... Read More
Tuesday, 12 December 2017 23:50
Jorge Andrade
Hi Scott, here is the translation on Spanish of your article. I tried to respect your style, and on the pictures i put a text box ... Read More
Saturday, 23 December 2017 21:10
42880 Hits
19 Comments

To keep the site live and make improvements Please consider Donating. Thank you for your donation.