What's New In The 3D Printer World

Prevention is the key

Over the last few weeks there have been posts on social media relating to fires being caused by 3D printers.

Continue reading
  5372 Hits
  3 Comments
Recent Comments
Kevin West
As mention this is controversial, and think this is a preferential choice. I have never had any issues with tinning wires includin... Read More
Sunday, 05 August 2018 01:23
5372 Hits
3 Comments

X - Y Axis

X - Y Axis

One of the biggest flaws in my opinion of the X5S are the belt pulley mounts, as the load placed on them when the belts are in tension is located in one point on each fixing.

Continue reading
  4605 Hits
  0 Comments
4605 Hits
0 Comments

Z - Axis Linear Rail Installation

Z - Axis Linear Rail Installation

Preparations the key for the rails to run correctly, and lubricating the rails is best done prior to installation.

Continue reading
  4735 Hits
  0 Comments
4735 Hits
0 Comments

Z Axis Mount

Z-Axis Mount

I reccomend you replace the Z-Axis mount even if you do not intend to use a linear rail.

Continue reading
  4734 Hits
  0 Comments
4734 Hits
0 Comments

Customized Tronxy X5S Frame

The frame of the printer is the most important part, and if you get this part of build wrong everything else will go out of whack very quickly. I do not recommend printing certain part for strength and stability reasons.

Continue reading
  4839 Hits
  0 Comments
4839 Hits
0 Comments

Customized Tronxy X5S

I keep on getting asked to keep members of Groups on Facebook to keep the upto date with the Customisation of My second X5S. So I have created a special section on our forum to create a build log,

Continue reading
  7207 Hits
  1 Comment
Recent comment in this post
Gernot Lepuschitz
Hi - you wrote: "So I have created a special section on our forum to create a build log..." - but I cannot find this section in th... Read More
Thursday, 24 October 2019 09:03
7207 Hits
1 Comment

Tap Drill Chart

There are six categories of standard taps. We have broken down the drill size recommendations into those six categories which appear below

 

Metric Size

Letter Size

Metric taps

milimeter Thread

Continue reading
  4761 Hits
  0 Comments
4761 Hits
0 Comments

The Shop Is Back

After working on the shop site over the weekend.The team are happy to announce the site is back up and running...

  5024 Hits
  0 Comments
5024 Hits
0 Comments

G Codes and M Codes for 3D printing

          You can customize the beginning and ending code that your slicer adds to the gcode files it produces to automate certain tasks or produce a more desired behavior. Below are suggestions for these codes.

For a list of gcode commands and their usage continue to the bottom of the post.

Continue reading
  9682 Hits
  2 Comments
Recent Comments
Dan Gould
How about printers that have dual extruder heads? Are there codes for those? Thanks Dan
Friday, 09 February 2018 13:49
Dan Gould
I think it would need to recognise T# as a Tool selection. More investigation needed by me I think. I'd like to modify my Tronxy X... Read More
Friday, 09 February 2018 13:53
9682 Hits
2 Comments

How to calculate power requirements of 3D Printer & safeguard Controller

          Most new users to 3D Printing buy a kit due to the low cost in owning one, however
most do not have any engineering background. This in it's self is not an issue as we
want to encourage new users to this fascinating hobby,
but can cause problems when users decide to modify or upgrade, repair their printer.
The power supply that come's with you printer has some marking on it regarding to the power "WATTS", however most will not show the most important factor the
number of "AMPS" the Power Supply will actually deliver......

Continue reading
  9049 Hits
  1 Comment
9049 Hits
1 Comment

We Have Gone Live

We Have Gone Live.

Welcome you all new members who have joined us.

While the site is new there might be a few buggy issues, and to help us give you a great user experience let us know if you find something wrong.

Also if you think of somthing to add to any of the main areas of the site do tell us.

Many Thanks For Joining.

The Team.

Continue reading
  4864 Hits
  0 Comments
4864 Hits
0 Comments

We are close to completion

It's getting there

Hopefully by the end of the weekend the website will be ready for everyone to enjoy.

  3924 Hits
  0 Comments
3924 Hits
0 Comments

To keep the site live and make improvements Please consider Donating. Thank you for your donation.